Mobile pool service across Corona, CAMon–Fri 7am–5pm · Sat 8am–2pm
Questions? Reach us at 951-545-4118📞 Call💬 Text

Home › Blog › Pool Chemistry Guide

Pool Chemistry Guide: How to Balance Your Pool Water

The numbers that matter, what to add when they're off, and why Corona pools drift the way they do.

Balanced pool water has free chlorine of about 1 to 3 ppm, pH of 7.4 to 7.6, total alkalinity of 80 to 120 ppm, calcium hardness of 200 to 400 ppm and stabilizer (CYA) of 30 to 50 ppm. Lower pH with muriatic acid or dry acid, raise alkalinity with baking soda (sodium bicarbonate), and shock weekly in summer or after heavy use or rain. Our weekly pool cleaning in Corona tests and balances all of this on every visit, with chemicals included.

The Target Numbers

  • Free chlorine: 1 to 3 ppm (higher if your stabilizer is high; salt pools often run 2 to 4 ppm)
  • pH: 7.4 to 7.6 is ideal; 7.2 to 7.8 is acceptable
  • Total alkalinity: 80 to 120 ppm
  • Calcium hardness: 200 to 400 ppm for plaster pools
  • Stabilizer (cyanuric acid, CYA): 30 to 50 ppm; salt pools often 60 to 80 ppm
  • Salt (salt pools only): usually 2,700 to 3,500 ppm, per your cell maker

Test chlorine and pH at least twice a week in summer, and alkalinity, calcium and stabilizer every week or two.

How to Lower pH in a Pool

  1. Test pH and alkalinity first.
  2. Add muriatic acid or dry acid (sodium bisulfate) in small doses, following the label for your pool size. Add acid to water, never water to acid.
  3. Pour it slowly in front of a return jet with the pump running.
  4. Wait at least 4 to 6 hours, then retest before adding more.

High pH is the most common problem in Corona. Salt systems, new plaster and aeration from waterfalls all push pH up.

How to Raise Alkalinity in a Pool

Add baking soda (sodium bicarbonate). About 1.5 pounds per 10,000 gallons raises total alkalinity by roughly 10 ppm. Add it in stages, let the pump run for several hours, and retest. Baking soda raises pH a little too, so check both.

How Often Should You Shock Your Pool?

Shock once a week in Corona's summer heat, and also after a pool party, a heavy rain, a dust storm, or any time the water looks dull or the chlorine reads near zero. In cooler months, every two weeks is often enough if chlorine holds steady. Shock in the evening so the sun doesn't burn it off.

Calcium and Corona's Hard Water

Corona's tap water is hard, and evaporation concentrates the calcium over time. That shows up as white scale at the tile line and inside heaters and salt cells. You can't add a chemical to remove calcium; the fix is keeping pH and alkalinity in range so it stays dissolved, and a partial drain and refill when it climbs too high. See acid wash and tile cleaning for scale that has already formed.

When the Numbers Won't Stay Put

If chlorine disappears overnight, the water stays cloudy, or pH climbs every few days, there is usually an underlying cause: high stabilizer, a dirty filter, short pump run times or algae starting. See cloudy pool water and why is my pool green.

Common Questions

What should my pool chemicals be at?

Free chlorine 1 to 3 ppm, pH 7.4 to 7.6, total alkalinity 80 to 120 ppm, calcium hardness 200 to 400 ppm and stabilizer 30 to 50 ppm. Salt pools also need 2,700 to 3,500 ppm salt.

How do I lower the pH in my pool?

Add muriatic acid or dry acid in small doses in front of a return jet with the pump running, wait 4 to 6 hours and retest.

How do I raise alkalinity in my pool?

Add baking soda (sodium bicarbonate). About 1.5 pounds per 10,000 gallons raises alkalinity by roughly 10 ppm.

How often should I shock my pool?

Weekly in summer and after heavy use, rain or dust storms. Every two weeks in cooler months is often enough if chlorine holds.

Why does my pool pH keep going up?

Salt systems, new plaster, waterfalls and high alkalinity all push pH up. Lowering alkalinity toward 80 ppm helps it stay steadier.

Ready for a Cleaner Pool?

Spend your weekends in the pool, not cleaning it.